![setting table position in sheetcam setting table position in sheetcam](https://www.windowslatest.com/wp-content/uploads/2018/09/Edge-loads-ISO-download-page.jpg)
This would not show up in the GCode, but it would happen just before a G04 and the two would some together. The ESS precision delay was requested by some people who work with VERY thin metals, and and wanted a very short and precise delay (like 25 ms). Which one should I use?Ī: The SheetCam delay would just be a plain G04 P#.# delay. In the cutting tool there is a “pierce delay” and an "ESS delay after Arc Okay in seconds”. It looks like there is one is the cutting tool and the one in the post processor. Q5: I am just looking at the setting is SheetCam and it seems like there are multiple places to set up the delays. It adds a little bit of cost, but it makes everything run so much smoother once it is set up for your machine. Having Anti Dive 2 automatically enable and disable Height Control is a significant advantage for the WarpRunner and this is why we recommend SheetCam. (If someone else did want to do that, I would gladly post their post processor on our site.)
SETTING TABLE POSITION IN SHEETCAM HOW TO
This took about 2 weeks to get everything working nicely, and how to make it work correctly in Fusion 360 is a huge question that I don't have time to work on and perfect. SheetCam will look at the GCode it is generating and intelligently decide where to place "M62P5" to allow THC Z axis motion and "M63P5" to prevent THC Z axis motion. However, Anti Dive Choice (Mode) 2 (lead ins, lead outs and small circle / arc radii) would be a different output, say Output #5. Assuming that the torch is on Output #3 you would use "M62P3" to turn the torch on and "M63P3" to turn the torch off. It would be easy to modify an existing post processor to do that (by changing the M3 and M5 commands). Q4: Do I have to use SheetCam with the WarpRunner? Could I just write a post processor for Fusion 360 (Vetric or another CAD package)?Ī: You certainly could write a post processor to make another CAD package control the torch, by using one set of M62/M63 GCode commands to turn the torch on and off. However if you are using an ESS, you could choose not to use the ESS's Firmware based Height Control and instead use the slower and less responsive Mach4 Height Control. The ESS does not need OOB motors to perform Height Control. We wrote everything from the ground up (for Height Control in Mach4) and Mach4 has nothing to do with Height Control when the ESS is used with a WarpRunner, TMC3in1 or an Up / Down H.C. Q3: Are OOB (Out of Band or non coordinated) motors required with the WarpRunner and ESS?Ī: Out of band motors are only required for the way Mach4 handles Height Control, without the ESS. This process loop the repeats continuously. The ESS responds to the commanded velocity and makes the Z axis move and then reports the Z positions back to Mach4. On/Off button, Arc Okay, and all the other Anti Dive modes) then the WarpRunner will compare the current tip voltage to the target tip voltage 2'500 times per second and command a Z axis velocity up or down to get the two voltages to match.
![setting table position in sheetcam setting table position in sheetcam](https://s3.amazonaws.com/fourthbit-blog/2013-11-27-essential-css-positioning-for-everyone/absolute.png)
If Height Control is allowed ( by the H.C. Q2: How does the WarpRunner and ESS perform Height Control?Ī:The WarpRunner measures the current (actual) tip voltage over 187'000 times every second and filters that data down to about 2'500 data points per second. Please just believe us and use Mach4 and SheetCam. Other than this documentation, we won't support Mach3 with the WarpRunner.These features are not available in Mach3. This will eliminate may many crashes and save you lots of frustration and material.
![setting table position in sheetcam setting table position in sheetcam](https://i.ytimg.com/vi/2IQoaix4t6A/maxresdefault.jpg)
![setting table position in sheetcam setting table position in sheetcam](https://i.pinimg.com/originals/0a/8d/56/0a8d56b9f9957ee9bca3b7dd9ddc243c.jpg)
Mach4 had all of the Height Control written from the ground up inside of the SmoothStepper and its plugin.If something is going wrong Mach4 will report what is going wrong, Mach3 won't.If you value your time whatsoever, and you want to avoid frustration, use Mach4 and don't use Mach3.